2025 Vermeer® Stump Cutters SC382

Information

2025 Vermeer® Stump Cutters SC382

A 37-hp (27.6-kW) gasoline engine provides stump grinding professionals with the performance needed to power through tough jobs.

The SC382 stump cutter is equipped with standard four-wheel drive to offer traction and maneuverability in difficult transport conditions.

The SmartSweep™ control system helps improve efficiency and productivity at the stump while helping to minimize wear and tear on the machine.

Without the dual wheels installed, the SC382 is only 35 in (89 cm) wide, allowing it to enter narrow backyard gates and access tight jobsites.

On graded terrain, the SC382’s footprint maximizes stability and provides a consistent cutting experience.

Options for both the Vermeer cutting system (VCS) or Yellow Jacket™ cutter system give you the choice to select the wheel that is right for your operation and ground conditions.

Designed for easy maintenance, helping you get to work.

Protect your stump cutter investment with extended service coverage options.

The operator presence system allows the cutter wheel to automatically stop when the operator releases the hydraulic cutter wheel controls.

VermeerOne™ Platform isn’t just a tool or platform. It’s an experience — one designed to simplify equipment management, empower users with real time data to make smarter decisions, and help maximize productivity and profitability.

Features may include:

  • More power, more torque
  • Built with more options for efficiency and productivity
  • Designed for serviceability and jobsite flexibility

Photos

Highlights

  • Waco, Texas
  • 2025
  • Vermeer®
  • Stump Cutters SC382
  • Gas
  • Available
  • 50.1 in
  • 53 in

Specifications

  • 2025
  • Vermeer®
  • Stump Cutters
  • SC382
  • Stump
  • 2
  • EFI
  • 49 ft-lb
  • Spin-on
  • Medium: Air
  • Gross (Maximum): 37 hp
  • Briggs & Stratton Vanguard
  • Dry-type safety element and restriction indicator
  • Max Fuel Consumption: 3.2 gph
  • Gas
  • Electric clutch with brake
  • Steerable Axle Type: Hydraulic steering, oscillating axle
  • Rigid/fixed (rear)
  • 5.7"x 8" (14.5 x 20.3 cm) dual standard
  • Spring-applied, hydraulic release at rear motors
  • 400 CCA
  • 20/50 amp (rpm-based)
  • System Voltage: 12 V | Shutdown System: Engine low oil pressure
  • Cutterwheel: 1560 rpm | Low Speed Travel: 65 ft/min | High Speed Travel: 130 ft/min
  • System relief: 2470 psi
  • Flow at Maximum RPM: 6.4 gpm
  • System Type: Open-loop series system
  • Welded tube and plate steel
  • Warning: Oil pressure, engine fault, operator presence status, clutch engage/disengage status
  • Maximum Angle of Continuous Operation: 25 deg | Cutterwheel Diameter without Teeth: 17 in | Cutterwheel Thickness: .5 in | Cutterwheel Straight Line Dimension: 47 in | Cutterwheel Cut Above Ground: 24 in | Cutterwheel Cut Below Ground: 15 in | Chip Containment: 7.5 cu ft | Jackshaft Dimension: 1.3 | Bearing Dimensions: 1.3 bore | Cutterwheel Shaft: 1.8" (4.8 cm) | Bearing Dimensions - Secondary Belt: 1.8" (4.8 cm) double spherical roller pillow block | Degree of Oscillation: 12 deg | Blade Travel Above Ground: 8 in | Blade Travel Below Ground: 2.5 in
  • 53 in
  • 118 in
  • 50.1 in
  • Transport (without duals): 35.5 in
  • Tank: 10 gal
  • Tank: 6.5 gal
  • Volume with Filter: 2.5 qt
  • 1950 lbs
  • Number of Teeth: 20 | Number of Indexes: 2 | Number of Pockets/Teeth: 20 | Jackshaft Bearing Type: Sealed ball | Filtration Method: 10 micron fill strainer and 6 micron return filter | Flow Control: SmartSweep | Directional Control: Electric over hydraulic | Switches: Two-speed 2x4 and 4x4 ground drive, cutter wheel engage/disengage, creep, blade (if applicable) | Controller: Danfoss | Control Station Description: Fixed side location | Axle: Rigid
  • V-belt
  • Recommended: 10W30 | hydraulic Recommended: Vermeer HyPower 68
  • Number of Primary Belts: 2 individual (matched pair) | Number of Secondary Belts: 6 banded