Engine
Engine Manufacturer
Deutz | Cutter Drive: Linkbelt | Chassis Option One: Dexter | Chassis Option Two: Dexter
Displacement
G2.9 L
Cylinder Liners
4
Engine Power
Gross Horsepower (Maximum) 72.4 hp
Engine Torque, Maximum
154 ft-lb
Air Cleaner
2-stage dry with safety element
Oil Filter
Spin-on
Cooling
Medium: Liquid cooled
Bore
2.4 in
Motor
Displacement
Motor: 28.3
Motor Type
Manufacturer: White
Fuel System
Fuel System
Max Consumption: 4 gph
Fuel Type
Unleaded and E10 gasoline
Drivetrain
Clutch
Type: Clutchless PTO | Drive Engagement: Belt tensioner
Suspension
Suspension
Torsion | Option Two: Torsion
Wheels & Tires
Tires, Rear Specification
Option One: ST235/80/R16 Load Range E | Option Two: ST235/80R16 Load Range E
Battery
Battery
Group 24; 580 CCA
Electric
Alternator
95 amps
Electrical
System Voltage: 12 volt
Operational
Operating Speed
Feed: 118 ft/min | Drum/Disc: 2220 rpm
Operating Conditions
Actuation Force (BFSB): 34 lbs | Actuation Force: 34 lbs
Performance
Noise Level
119 dB(A)
Hydraulics
Airflow
580 cfm
Hydraulic Type
System: Open center
Hydraulic Pump
Flow at Maximum RPM: 3 gpm
Maximum Pressure
System relief: 2500 psi
Chassis
Frame Type
7" (17.8 cm) Z channel; .25" (0.6 cm) thickness
Hitch/Type
Pintle
Lights and Safety
Lighting
Trailer Type: LED
Dimensions
Dimensions
Maximum Angle of Continuous Operation: 30 deg | Feed Roller Minimum Distance to Drum: 1 in | Feed Roller Dimension: 20 " x 17 " (50.8 cm x 43.2 cm) | Infeed Throat Capacity: 12 " x 17.5 " (30.5 cm x 43.2 cm) | Pinch Point - Distance to End of Feed Table: 66.5 in | Distance from Feed Table to Ground: 26 in | Infeed Table Material Thickness: .2 in | Bottom Feed Stop Bar Diameter: 2 in | Bottom Feed Stop Bar Material Thickness: 11 GA | Normal Sensitivity: 22 deg | Reduced Sensitivity 12 deg | Material Capacity: 12 in | Thickness: 20 in | Drum/disc: Diameter 20 in | Drum/disc - Knife Thickness .6 in | Knife Size 0.63 " x 4.5 " x 9 " (1.6 cm x 11.4 cm x 22.9 cm) | Bedknife Size: 3.5 " x 17.3 " (8.9 cm x 43.8 cm) | Bedknife Thickness: 1 in | Bedknife Material: 1018 | Chute Rotation Angle: 270 deg | Tongue Description: 2.5" x 4.5" x .25" (6.4 cm x 11.4 cm x .6 cm) | Tongue Extension Extendable: 24" (61 cm) at 12" (30.5 cm) increments
Length
Feed Table Up, Tongue In: 160 in | Table Down, Tongue Extended: 208 in | Infeed Table: 32 in
Width
66.5 in | Infeed Table: 52 in
Height
101 in | Infeed Hopper: 12 in | Chute: 101 in
Fan Diameter
18.75-in suction
Wheels
Option One: 16 " x 6 " (40.6 cm x 15.2 cm)
Capacities
Fuel Capacity
Tank: 20 gal
Oil capacity
Volume with Filter: 8 qt
Features
Coolant Capacity (Engine and Radiator): 5.5 gal | Dynamic Capacity: 31400 lbs | Static Capacity: 53500 lbs | Chassis Option One: 5200 lb (2358.7 kg) | Option Two: 7000 lb (3175.2 kg)
Load Capacity, Land
Feed Roller Clamp: 350 lbs
Hydraulic Capacity
Tank: 7 gal
Weights
Weight
Option One: 4680 lbs | Tongue - Engine Option One: 520 lbs | of Feed Roller: 400 lbs | Drum/Disc With Shaft: 460 lbs
Features
Features
Feed Roller Orientation: Horizontal | Number of Feed Rollers: 1 | Number of Knives: 2 | Number of Feed Roller Motors: 1 | Reset Method: Green hold-to-run button | Reset Method: Green hold-to-run button | Positions: 4: E-stop, forward, neutral, and reverse | Safety Lock - Number of Positions: 2 | Useable Edges: 2 | Number of Paddles: 5 | Fixture Method: Weld-on | Number of Bearings: 2 | Cutter Drive: Spherical rollers | Rotation Type: Manual rotate with pin lock | Filtration Method 10 micron return; 100 micron suction | Gauges: Fuel and MFD | Switches: Droop, EcoIdle, and Sensitivity | Controller: Vermeer ACS | Shutdown System: High temp, low pressure | Chassis Type - Option One: Rubber torsional | Chassis Option Two: Rubber torsional
Oil Type
Recommended: 10W30 | Recommended: Vermeer VMF
Knife Quantity
Number of: 2 | Number of Bolts: 4
Construction Material
Drum/Disc: A8 chipper steel | Fender Description: Bolt-on steel
Belt Type
5V
