2025 Vermeer® Trommel Screens TR6400

Information

2025 Vermeer® Trommel Screens TR6400

Compatibility with smaller gauge wire increases the open screen area helping overall production of the machine, particularly in applications when processing wetter materials.

Screen changes can help improve jobsite efficiency, a particularly important feature when processing a range of materials that require frequent screen changes.

A low hopper infeed height helps to decrease loading cycle times and eliminates the need for loading ramps with most loaders.

A single large access door provides engine service access.

Lift bars lift and agitate material for thorough screening.

Operators can control the machine through either the Vermeer DP10 display mounted on the control panel.

Features may include:

  • Tough and compact design
  • Quick change tensioned screens
  • Complete control for maximized productivity

Photos

Highlights

  • Waco, Texas
  • 2025
  • Vermeer®
  • Trommel Screens TR6400
  • Model: 3.6L
  • Available
  • Operation: 295 in | Apron Opening: 37.5 in | Apron Conveyor Belt: 42 in
  • Operation: 16.7 ft | Apron Opening: 45 in | Hopper: 9.5 ft (2.9 m) from ground level at operating incline | Conveyor Belt Stacking: 10.5 ft (3.2 m) (conveyor @ 30 deg)

Specifications

  • 2025
  • Vermeer®
  • Trommel Screens
  • TR6400
  • General
  • Model: 3.6L
  • 4
  • Deutz
  • Spin-on
  • Dual element
  • Tier 4F (Stage IV)
  • Rating: 100 hp (74.5 kW)
  • Drum: 35.5 cu in (581.7 cu cm) displacement | Conveyor: 14.2 cu-in
  • Fuel Consumption: 3 gph (11.4 L/h)
  • Leaf spring
  • 445/50 R22.5
  • 950 CCA
  • System Voltage: 12 V, 120 amp alternator
  • Apron Conveyor: 0-15 fpm | Drum: 0-25 rpm | Collecting Belt: 360 ft/min | Fines Belt: 400 ft/min
  • 77.8 gpm @ 3000 psi (294.5 L/min @ 206.8 bar) | Drum Operation: 0-33.1 gpm (0-125.3 L/min)
  • Four independent hydraulic jacklegs | Fines Conveyor Frame: Part of trailer frame / Engineered structural frame
  • Maximum Engine Operating Angle (Operating angles do not indicate safe machine operating angles): 30 deg | Hopper Opening: 11.7 ft x 5.3 ft (3.57 m x 1.6 m) | Drum Diameter: 6.5 ft | Thrust Bearing Diameter: 4 in | Thrust Bearing Face: 2 in | Brush Diameter: 14 in | Brush Assembly Support: Two 1.25 in (3.2 cm) sealed ball bearings/brush | Head/Tail Pulley Type: 8 in (20.3 cm) crowned | Head Pulley Bearing: 1.75 in (4.4 cm) double roller | Tail Pulley Takeup: 6 in | Self-Cleaning Return Idlers: 4 in (10.2 cm) rubber disk x 3 | Head Pulley Type: 8 in (20.3 cm) crowned | Head Pulley Bearing: 1.5 in (3.8 cm) pillow block | Self-Cleaning Tail Pulley Dimensions: 8 in diameter, 38 in wide, crowned wing pully | Head Pulley Takeup: 8 in | Drum Angle Adjustability: 0-5 deg | Conveyor Belt Type: 220 lb (99.8 kg), 2 ply, 2/6" x 1/16" (4.8 mm x 1.6 mm)
  • 40 ft
  • 99 in
  • 13.1 ft
  • Belt: 36 in
  • Bottom: 37.5 in
  • Operation: 54 ft | Apron Conveyor: 12.4 ft | Drum: 20 ft | Collecting Conveyor: 16 ft | Fines Conveyor: 23.5 ft
  • Operation: 295 in | Apron Opening: 37.5 in | Apron Conveyor Belt: 42 in
  • Operation: 16.7 ft | Apron Opening: 45 in | Hopper: 9.5 ft (2.9 m) from ground level at operating incline | Conveyor Belt Stacking: 10.5 ft (3.2 m) (conveyor @ 30 deg)
  • Tank: 50 gal
  • Tank: 80 gal | 6.5 cu yd
  • Oil Volume with Filter: 10 qt
  • Approximately 180 cu yd (137.6 cu m) per hour with 0.5 in (1.3 cm) screens installed and material with moisture less than 40%
  • 37000 lbs | Hitch: 4200 lbs
  • Radiator Fan: Suction | Apron Conveyor Rollers: 5 CEMA "D" x 17 in (12.7 x 43.2 cm) | Drum Support Description: 8 polyurethane trunnion wheels on pivoting bogeys 8 od x 4 in wide (20.3 x 10.2 cm) | Drum Drive Chain: 140 extended pin/extended width | Maximum Screen Panels: 8 | Rubber Flashing: Adjustable corded rubber | Idler Type: 4 in (10.2 cm) CEMA "B" straight | Troughing Idler Type: 20 deg CEMA "B" with permanently sealed bearings spaced at 40-in centers | Axle: Leaf spring
  • Bristle: Polyethylene
  • Recommended: Mobil 15W40